A VERY EASY CHUNKY Beanie
Hello everyone! Today's free pattern is a cute little chunky beanie. I have been working on a lot of large and intricate patterns for knitting and crochet recently, so I decided to take a break from them and make something simple, which I have not done in a while. Over the weekend I made this simple beanie hat in between working on a tank top pattern submission and a cocoon wrap pattern. It has been a long time since I made a hat this simple, not since I was much younger and just starting out with knitting. The hat only took three hours to make, and the pompom took about fifteen minutes. Wanting to share some easy projects on my website, I decide to craft a pattern for this little hat.
This is a great project if you are wanting to take a break from something complicated (like I did), if you are a beginner knitter, if you would like to make a gift for someone, or if you are simply looking for something to do. A note to beginner knitters, if this your first time using chunky yarn, especially one made from natural fibers such as wool or alpaca, knit carefully as natural fibers this size are often delicate and can pull apart easily if too much force is used.
For $2.00, this pattern is also available for purchase through Ravelry. You can access the pattern via Ravelry link below. A free version of the PDF is also available on LoveCrafts.
© Kari-Elyssa Designs 2020-2022. All Rights Reserved. This pattern is strictly for personal use only. You are not permitted to sell finished versions of the hat without written consent to do so. Do not copy, translate, alter, reproduce, redistribute, share, sell, repost, or distribute the pattern or pattern page in any way or any media format. Use of the feature photographs is prohibited. Thank you!
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
11 sts and 15 rows= 4" (10cm) using larger needles over Stockinette Stitch
This hat will fit a typical adult head.
Finished circumference: 19" (48cm). The hat will stretch slightly to fit larger sizes.
Finished height: 8"(20.3cm) long without the pompom and 10.75" (27.3cm) including the pompom
With smaller needles, cast on 52 sts.
Rnd 1: *K1, p1; repeat from * to end of round.
Work the established pattern until ribbing measures 1.75” (4 cm) from cast on edge. Place stitch marker for beginning of round. Switch to larger circular needles and begin work on the body of the hat.
Rnd 1: Knit all stitches.
Repeat Rnd 1 until piece measures 6.25” (16cm) or desired length from cast on edge.
Switch to DPNs.
Rnd 1: *K2tog, k2; repeat from * to end of round (39 sts remain).
Rnd 2: Knit all stitches.
Rnd 3: *K2tog, k1; repeat from * to end of round. (26 sts remain).
Rnd 4: Repeat Rnd 2.
Rnd 5: K2tog to end of round. (13 sts remain).
Rnd 6: Repeat Rnd 2.
Fasten off, leaving a 22” (56cm) tail. Thread the tail onto a tapestry needle and insert it through all the remaining stitches, going clockwise as if to purl. When all of the stitches have been threaded, remove DPNs and pull the tail to close up the top of the crown. Pull tail to the inside of the hat and tie a knot to secure the closed stitches.
Weave in ends.
If using, attach the pompom to the hat and weave in any additional ends.
Block as desired.
I hope you enjoyed this hat! If you have any questions or concerns regarding the pattern, please feel free to contact me here. While I work extensively to make sure patterns are free of errors, no one is a perfect machine, and mistakes happen from time to time. I will gladly make an update or post an errata link if needed.
Your comment will be posted after it is approved.
Leave a Reply.
Free patterns are usually (but not always) posted on Friday! These patterns, which include knitting, crochet, weaving, and sewing, are all simple to make. I also have purchasable version available for most what is featured. Happy crafting!